一二三四观看视频社区在线,又色又爽又黄18禁美女裸身无遮挡,日本丰满少妇xxxx,欧美性猛交xxxx富婆

液壓機拉伸試驗機:拉力測試機偏移常見故障檢修

瀏覽量:2105? 來源:www.yiaomachine.com??作者:全力測試 時間:2019-10-12

  液壓萬能試驗機:拉力試驗機位移出現故障后的維修步驟:

  Hydraulic universal testing machine: Maintenance steps after displacement failure of tension testing machine:

  1、首先對位移傳感器進行檢查:

  1. First, the displacement sensor is checked.

  因?yàn)槔υ囼?yàn)機系統是一個閉環系統,要想知道是哪個部分出現了問題,就一定要切斷系統中的回路,使其成為一個開環的系統。從而可以判斷試驗機的傳感器信號是不是正常。這個時候也要斷開位移傳感器的反饋信號,使其成為開環。此時工作站發出一個控制動作器移動的信號,對傳感器的反饋值進行測量,在幾次重復之后,傳感器的反饋數據值可以組成一條直線,這個直線是線性變化的,從而就可以知道傳感器是不是有問題了。

  Because the tension testing machine system is a closed-loop system, in order to know which part of the system has problems, it is necessary to cut off the loop of the system and make it an open-loop system. So we can judge whether the sensor signal of the test machine is normal or not. At this time, the feedback signal of the displacement sensor should be disconnected to make it open-loop. At this time, the workstation sends out a signal to control the movement of the actuator, and measures the feedback value of the sensor. After several repetitions, the feedback data value of the sensor can form a straight line, which changes linearly, so that we can know whether the sensor is in trouble.

  2、其次就是對拉力試驗機的放大器單元的檢查:

  2. Next is the check of the amplifier unit of the tension testing machine.

  在已經排除了位移傳感器的問題之后,因?yàn)槔υ囼?yàn)機的系統是一個閉環系統,放大器單元的正常與否是一定要進行檢查的,方法就是斷開放大器單元的輸出信號。將輸出接線拆除,在放大器單元加上一個直流輸入信號,然后測量擺錘沖擊試驗機放大器單元的輸出情況,在重復試驗幾次之后,得到一個放大器單元輸出信號的線性變化趨勢數據,這樣就可以知道放大器單元是不是有問題了。

  After eliminating the problem of displacement sensor, because the system of tension testing machine is a closed-loop system, whether the amplifier unit is normal or not must be checked by disconnecting the output signal of the amplifier unit. Remove the output wiring, add a DC input signal to the amplifier unit, and then measure the output of the amplifier unit of the pendulum impact tester. After repeated tests, the linear trend data of the output signal of an amplifier unit are obtained, so that we can know whether the amplifier unit is in trouble.

  3、最后就是檢查拉力試驗機的系統設定是否正常:

  3. Finally, check whether the system settings of the tension testing machine are normal:

  工作站當中的動作器的行程正常情況下應該是±50mm,如果與這個數字不符,那么就是系統設定的問題,就需要重新的設定系統。要是工作站的顯示板上面的顯示值依舊不正確,那么就可以判定只有重新的標定位移系統,才可以解決這一類的問題。

  Actuator travel in the workstation should normally be (+50mm). If it does not match this number, then it is the problem of system settings, and the system needs to be re-set. If the display value on the display board of the workstation is still incorrect, then it can be determined that only the re-positioning and moving system can solve this kind of problem.http://www.yiaomachine.com



聯系我們
  • 服務熱線:4008005579
  • 銷售熱線:0531-55771199/2199/3199 18615260858
  • 聯系郵箱:quanlitest@163.com
  • 工廠地址:山東省濟南市槐蔭區西沙西路569號
關注我們
  • 掃碼關注我們
  • 掃碼關注我們
日韩A人毛片精品无人区乱码| 日本高清色WWW网站色噜噜噜| 亚洲婷婷五月综合狠狠爱| 亚洲AV无码专区色爱天堂老鸭窝| 6080午夜三级中文在线观看| 国产剧情av麻豆香蕉精品| 国产乱子伦午夜精品视频| 一卡二卡亚洲乱码一卡二卡| 久久婷婷五月综合色精品首页| 亚洲欧美成人一区二区三区| 国产超高清麻豆精品传媒麻豆精品| 亚洲日韩国产精品乱-久| 国产在线看片免费人成视频| 亚洲精品无码午夜福利中文字幕| 最新日韩精品中文字幕| 欧美成 人影片 免费观看| 青春禁区视频在线观看直播免费| 黑人大群体交免费视频| 亚洲综合无码AV在线观看| 国产精品久久久久久无码五月| 亚洲精品无码久久千人斩| 熟女无套高潮内谢吼叫免费| 精品国产AV无码一区二区三区| 亚洲高清国产拍精品5G| 亚洲AV日韩AV永久无码绿巨人| 国产另类ts人妖一区二区| 无码人妻少妇色欲AV一区二区| 夜夜爽77777妓女免费看| 无码国产精成人午夜视频不卡| 日产精品卡三卡在线| 全部孕妇毛片丰满孕妇孕交| 亚洲AV永久无码精品三区在线| 东京热无码一区二区三区AV| 久久精品国产亚洲AV成人| 又湿又紧又大又爽又A视频| 免费人成在线观看成人片| AV老司机色爱区综合| 国产AV天堂无码一区二区三区| 看全色黄大色大片免费久久| 国产成人精品一区二区秒拍| 精品国产乱码一区二区三区|